SPEEDLINER PRO™ Easy Sprayliner – Mixing, Application & Curing Guide

A practical guide to preparing, mixing, spraying, curing, and cleaning for SPEEDLINER PRO™ Easy Sprayliner (2K polyurethane/polyurea hybrid).

Product Overview

SPEEDLINER PRO™ Easy Sprayliner is a 2K polymer spray liner designed for pickup beds, LandRovers, van floors, and smaller protective lining applications. Once cured, it delivers tough wear protection with anti-slip texture and strong UV performance.

Available in Black (Pre-Coloured) and Self Colour versions.

Key Benefits

  • Easy to use: pour – shake – spray
  • Quicker drying and curing than many comparable products
  • Kit sizes available for small to large applications
  • No colour restorer required
  • Protects against rust, scuffs/scrapes, water ingress, and extreme temperatures
  • Fully flexible even at very cold temperatures
  • Sound deadening properties
  • Can be applied using an underseal/shutz type spray gun, brush, or roller (for different textures)

Kit Quantities

  • 1 x 1 Litre Kit: Part A polymer + Part B activator (Pre-Coloured or Self Colour)
  • 4 x 1 Litre Kit: Part A polymer + Part B activator (Pre-Coloured or Self Colour)

Mixing Ratio

3:1 (Pre-measured Part A + Part B)

Specification (At 20°C / 68°F)

  • Pot Life (once mixed): approx. 10 minutes
  • Touch Dry: approx. 35 – 45 minutes
  • Light working duty: after 24 hours
  • Regular duty: 3 – 4 days (typical)

Preparation Guidelines

SPEEDLINER PRO™ Easy Sprayliner can be applied to most substrates, but surface preparation is essential:

  • Pre-painted surfaces: abrade with 80 grit and ensure surface is free from dirt and rust
  • Wood: does not need abrasion but must be clean and dry
  • Fibreglass / GRP: abrade with 80 grit, clean thoroughly, then apply SPEEDLINER PRO™ AP101™ Primer / Bonding Agent

Important: Do not use any silicone-based sealing products.

For best results, use SPEEDLINER PRO™ Wipedown Cleaner Blend.

Bare Metals (Additional Requirement)

  • Rough sand the metal surface
  • Clean thoroughly
  • Apply a light coat of SPEEDLINER PRO™ Etch Primer
  • Then apply a light coat of SPEEDLINER PRO™ AP101™ Primer / Bonding Agent

Mixing & Application Instructions

1 Litre Kit – Pre-Coloured Black

  1. Shake the pre-measured / pre-coloured hardener (250ml Part B) for 10 seconds
  2. Pour Part B into the SPEEDLINER PRO™ Part A tin
  3. Replace cap and shake vigorously for 60 – 90 seconds
  4. Attach tin to an underseal / shutz gun and spray immediately at 5 – 6 BAR (60 – 80 PSI)

Important: Mix one can at a time and use within 5 minutes. Do not mix and leave to stand.

4 Litre Kit – Pre-Coloured Black

  1. Shake the Part B hardener tin (850ml) for 10 seconds
  2. Using the mixing cup provided, add 200ml hardener to one Part A tin
  3. Replace cap and shake vigorously for 60 – 90 seconds
  4. Spray immediately at 5 – 6 BAR (60 – 80 PSI)

Important: Mix one can at a time and use within 5 minutes. Do not mix and leave to stand.

1 Litre Kit – Self Colour

  1. Add 30ml colour pigment to the Part B hardener tin (250ml)
  2. Replace cap and shake for 10 seconds
  3. Pour Part B (hardener + colour) into Part A
  4. Replace cap and shake vigorously for 60 – 90 seconds
  5. Spray immediately at 5 – 6 BAR (60 – 80 PSI)

Important: Mix one can at a time and use within 5 minutes. Do not mix and leave to stand.

4 Litre Kit – Self Colour

  1. Add 120ml colour pigment to the Part B hardener tin (850ml)
  2. Replace cap and shake for 10 seconds
  3. Using the mixing cup provided, add 200ml hardener/colour to one Part A tin
  4. Replace cap and shake vigorously for 60 – 90 seconds
  5. Spray immediately at 5 – 6 BAR (60 – 80 PSI)

Important: Mix one can at a time and use within 5 minutes. Do not mix and leave to stand.

Spraying Technique

  • Spray using an even side-to-side sweeping motion
  • Maintain a spray distance of approximately 12 – 14 inches from the surface for standard coverage/texture
  • If product begins to set, shake the tin vigorously to loosen the liquid
  • Subsequent coat(s) can be applied within 3 – 5 minutes

Touch-Ups & Recoating Windows

  • Touch-ups can be carried out within 48 hours of previous coats
  • Before touch-ups within 48 hours: wipe surface using SPEEDLINER PRO™ Wipedown Cleaner
  • After 48 hours: lightly sand, clean, then apply a light coat of AP101™ Primer/Bonding Agent before re-coating

Texture Finishes

  • Apply first coat normally
  • Apply a second coat from slightly further away: approximately 16 – 18 inches from the surface

Fogging Coat Tip (Large Areas)

After spraying large areas, if you want to lose a wet/dry patchy appearance, mix one kit and apply a light fogging coat over the full area from a distance.

Note: Leave all applications free to air.

Cleaning (Equipment)

Clean all equipment thoroughly using gun wash / standard thinners immediately after use.

Temperature Guidance

  • Do not use in extreme hot or cold temperatures
  • Ideal application temperature: 15°C to 22°C (approx. 58°F to 71°F)

Handling & Use Notes

  • Do not place or move sharp/heavy objects on the surface until fully cured (typically 3 – 5 days)
  • For professional use only – read instructions fully before use
  • This product contains hazardous material – refer to product label and technical data/safety data sheets for full handling information
  • Apply in a suitably ventilated area and always wear appropriate respiratory protection and protective clothing